As thousands of Kiwis prepare their boats to make a splash over summer, fishing expert Nicky Sinden has urged boaties to ensure their journeys don't sink before their vessels even hit the water.

It is estimated there are up to 200,000 crafts on trailers parked in backyards and driveways across New Zealand. Boat trailers account for about a third of all trailers in the country.

Each year, on average seven people are killed and a further 45 are seriously injured as a result of a towing accident.

Sinden — host of Prime TV's ADOS Addicted to Fishing — said while the boating season was a time to enjoy, too many trips were ruined by a lack of basic towing knowledge and boat ramp etiquette.

"It is amazing how many people set off for a nice family day on their boat and it quickly turns to custard before they even get it into the water," Sinden said.

"I have seen a lot of boat ramp rage, when people lose the plot with each other for not following a few simple rules. I haven't seen any blood drawn yet, but on a few occasions it has been close."

To coincide with this weekend's On the Water Boat Show at Auckland's Viaduct Harbour, Ford NZ has launched a safety campaign highlighting the dangers of towing and giving boaties tips on how to mitigate risks.

More than one million people take to New Zealand waters in recreational craft each year.

But Sinden said newcomers and experienced boaties alike were falling foul of carelessness and bad tempered behaviour at boat ramps.

"I have seen some busy ramps where there are up to 10 vehicles with boats on trailers queuing to get into the water," she said.

"Tempers can get frayed and I've seen people get into a panic when impatient boaties waiting their turn start shouting at them which can lead to serious errors and accidents."

Sinden said common mistakes include people trying to get their boats off slippery ramps with bald tyres on their cars and not having vehicles powerful enough to tow trailers and craft off sand.

"The best way to make things go smoothly on the ramps is to pull over to the side before you get there and first make sure all the right equipment is in place, so that the boats can be launched quickly," she said.

"For newcomers, a good idea is to practice on days when the weather is horrible and ramps are quiet.

"Even when boats have been successfully launched, there is still plenty of potential for things to go wrong," Sinden added.

"I have seen people not tie their boats up before taking their trailer and car away from a ramp and as a result their craft has floated off and bashed into another, causing a lot of damage.

"I have even seen expensive boats sink because the owners have forgotten to put the plug in the bung hole, which is about as basic an error as you can get."

From the NZHerald. Sunday 28th Sept

Visit our stand at the 2014 Auckland On Water Boat Show. Stand number OS12A (Pavilion 3). Talk to Lloyd and the team for some great show specials!

For many kinds of boating, the outboard motor is the answer. But it comes with questions, too — which is better, two strokes or four? What's the right prop? Is the bigger motor the better motor? We've presented a few of the most debated questions to the experts, and here's how they answer them.

Question: Are four-strokes always better than two-strokes?
Answer: Are Fords better than Chevrolets? Paper better than plastic? When it comes to outboard power, the question is four-stroke vs. two-stroke. If you believe what you hear, the answer is etched across the stone board — four-strokes rule. But dig deeper and you find the answer isn't so clear.
First, the technical distinction. Four-stroke outboards, like the engine in the car in your driveway, burn straight gasoline within cylinders, circulating lubricating oil through a separate system. Oil and gas don't mix, unless there's a breakdown. Two-stroke engines, in contrast, burn a blend of gas and oil.
Traditional two-strokes were fed their oil-gas mix fuel by carburetor or injector into the cylinder through an intake valve. During part of this feeding, the exhaust valve was also open, and up to 30 percent of the fuel escaped unburned.
Jump ahead to two-stroke direct-fuel-injection (DFI) engines. The fuel is sprayed into the cylinder with precision timing while the piston covers the exhaust valve. There's no loss of fuel. (In four-stroke engines, thanks to their four piston strokes per cycle, intake and exhaust take place at separate times.) DFI two-strokes and four-strokes both deliver much better fuel economy than traditional two-strokes, since they're directed by computer and burn virtually all of the fuel. Evinrude's E-TEC two-stroke DFI engines inject fuel twice as fast as standard direct injection, even adjusting the fuel delivery and oil-gas mix as needed. We've tested the E-TEC engines, and they're just as smooth and almost as quiet as four-strokes while maintaining more traditional two-stroke power.
On the other side, four-stroke motors are also erasing what was a clear division just two years ago, the one that said two-strokes are inherently more powerful. The industry once envisioned a 100 hp limit for four-strokes because of their extra weight. But the limit has vanished. Witness Suzuki's new 300 hp, at just 604 pounds.
"It's a closer call than ever before," says Mercury spokesperson Eric Pope. "The biggest myth is the idea that two-strokes are noisy, smelly and not very fuel efficient. It isn't true today." Two versus four is now more a matter of boater preferences than ground-shaking practical distinctions. Through it all, both modern four-strokes and DFI two-strokes are mechanical marvels. Difference, What Difference?

• • Two-stroke DFIs are lighter than four-strokes with the same power, but the difference is shrinking.
• • Four-strokes are quieter than two-strokes, but the difference is shrinking.
• • Two-strokes generally provide a stronger hole shot, but the difference is shrinking.

Question: Are two motors better than one?
Answer: Max horsepower on your boat is 300. Should you install one 300 hp motor or two 150s? You'll mainly see duals (and triples) in offshore fishing applications. In most cases you can bet they've been installed for peace of mind for boaters who have visions of catastrophic loss of an engine at sea. Duals have also earned favor for making docking an easier task, thanks to the engines having props revolving in opposite directions. But for this protection against an unlikely event, and for simpler steering dockside, a boater pays more money upfront — a lot more. Rigging with a pair of motors means you have to duplicate the controls and generally complicates installation.
"In performance, it's a wash," says Suzuki spokesman Rick Hauser. "Three hundred horses are three hundred horses, whether it comes through one prop or two."
So it really comes down to economics. If the price difference is not an issue, then twins are worth considering. Otherwise, a single is the simpler call.
Doubles Anyone?

• Multiple motors only provide security against breakdown if they're truly independent, including fuel and power sources.
• Hanging multiple motors adds power only if they exceed the power available in a single.
• Another alternative is to run a single unit and add a satellite phone for breakdown recourse.

Question: Is high-octane gas best?
Answer: When high-compression engines came on the scene, the increased pressure in their cylinders sometimes caused fuel to explode too early. That preignition, called spark knock, was more than an irritating noise (although certainly that); it caused engine damage. The solution was to add materials to the fuel that would slow the ignition until the piston was ready for the spark plug to activate, which would avoid damage and make efficient use of that higher compression. So now, the higher the octane rating, the better the fuel can handle compression.
Sounds good. But the truth is high-octane fuel — usually 92 or 93 octane — is a waste of money for the majority of outboards. Most are built to run happily on 87 octane. Some manufacturers — such as Tohatsu — do recommend midrange fuel, usually 89 octane. Check your owner's manual, and fuel up with what it prescribes. Go above the recommended octane and you're giving away about 20 to 30 cents per gallon.
Fuel Facts

• Only high-performance engines need high-octane fuel.
• High-octane fuel in motors made for low-octane fuel nets no better performance, but bigger fuel bills.
• In a few cases, motor makers might prescribe midrange fuel, usually 89 octane.

Question: Should I rig with the biggest motor allowed?
Answer: Boat buyers years ago were made rightfully leery of boat packages when some dealers priced them with puny outboards, and then coached the consumer up to a more respectable power plant before closing the deal. Those who spent the extra bucks for a bigger motor were generally well-served; those who stayed with a small motor for the lower price point were often disappointed. Things are better now: There are fewer underpowered packages on the market. Still, bigger is generally better. One of the worst things you can do is under-power a boat. You'll never savor the performance built into the hull. You won't be as prepared to scoot from an approaching storm. Potential buyers of your boat down the road will cast a jaundiced eye. Going with the boat maker's maximum rating, found on the inspection plate, is a pretty safe bet. If you're on the fence, you can check with boat manufacturers, who generally have available test data on the boat of your choice powered with various makes and models of engines. Go for the Gusto

• Take sea trials with boats that have less-than-max motors. We've noted in tests that some smaller motors power boats -- particularly pontoons -- beautifully.
• For the biggest seas and the heaviest loads, you want the biggest boy on the back of the boat.
• When was the last time you heard someone say they bought a boat with too large a motor?

Question: Is any prop proper?
Answer: The maker of your outboard probably equipped it with a decent, middle-of-the-road propeller. If not, the dealer likely did. But if either of them installed the perfect prop for you, it was probably dumb luck: The correct prop depends on how you'll load your boat, and how you'll use it. First, some propeller basics. Props are measured in diameter and pitch. You remember diameter from high-school geometry, of course, but pitch? That's the theoretical distance the propeller would travel through one complete revolution if there was no slippage. Moving away from the prop itself for a minute, consider that engine manufacturers rate their product's horsepower at a specific rpm, setting rpm ranges for top-end operation. It can only hit that top-end bracket if it's powering the right propeller. If the prop allows the motor to over-rev, wear and friction can occur. If the propeller restrains the motor from reaching that prime range, it gets poor mileage and you risk other damage. You can protect your motor and improve its performance by picking the right pitch. You can test your prop by running your boat at wide-open throttle. (If you're over the maximum rpm, throttle down until the needle is within the manufacturer-suggested range.) Ashore, inspect the propeller to learn its pitch. Figuring that you get about a 200 rpm drop for each increase in pitch, try a different prop. A cupped propeller will also reduce rpm by about 200. Some dealers will even let you test a prop, provided you return it undamaged and promptly. As long as it hits but doesn't exceed the motor's top-end range, a prop delivering wide-open rpms toward the bottom of the range provides stronger hole shots, while those toward the top generate slightly higher top speeds.
Prop Points

• Prop condition can be more important than type: A damaged prop can destroy the engine spinning it.
• Stainless-steel props run truest and are five times as strong, but aluminum is cheaper and sacrifices itself to protect the lower unit.
• A four-blade prop beats a three-blade in time to plane, midrange speed and low-speed handling.

Question: Are outboards maintenance-free?
Answer: There is little you need to do to maintain a modern outboard — but what is still needed is vitally important. You can blow up an engine by neglecting its cooling needs, clog it up by ignoring potential fuel problems, bust it up by letting the lower unit sit over winter with leaky seals. Depleted zincs can invite corrosion. Dinged props can shake the stuffing out of bearings and other moving parts. Owners manuals have slim maintenance sections. That doesn't mean they're unimportant. Maintenance Mantras

• Keep the fuel tank topped to reduce the chances of condensation building up when the motor isn't in use.
• Add fuel stabilizer every time you add fuel — it's important now with ethanol fuels.
• Inspect the prop at every opportunity. A ding might cause chatter at cruising speeds, but a tiny one could go unnoticed — and still do damage.
• Look over the fittings and hoses; cool water needs to run through the motor to keep it from burning up.

http://www.boatingmag.com/